|
|
Aquatec
Products -> Component Lines -> Misc. Components -> Assorted Pumps -> Aquatec
| Part No . |
|
Description |
Quantity |
| CDP 6800 |
POWER: Pumps operate with low energy (only 14 watts), low voltage (12-24 volt) motors, powered with compatible transformers with world wide primary voltages available (100 VAC, 120 VAC, 230 VAC). Transformers are optional and must be ordered in addition to the pump.
MOUNTING: The "flexible or steel" base plates are included at no extra cost. The "Universal" base plate P/N 51-104 is available optionally at additional cost.
FITTINGS: Built-in 1/4" John Guest half cartridge fittings eliminate need for external fittings (unless elbows are required); 1/4" Jaco straight, 1/4" Jaco elbow fittings, or 8mm stem adapters for metric tubing are optionaly available.
INSTALLATION: The location and positioning of the pump may affect its' performance. Always consult the factory for recommendations that will optimize your system.
|
CDP 6800 Series Low Flow Booster Pump
Distinguishing Features
Toughest, most durable pump on market
Adjustable max. outlet psi (regardless of feed pressure)
Expels trapped air (no more air locks)
Can be mounted w/pump head up or down
More flow at extremely low inlet pressures
Engineered composite plastics
New motor venting system to remove moisture
Pressure switch and transducer options
EMI/RFI electronic noise suppression
100% final performance tested.
Key Operating Benefits
Boosts pressure 40 to 120 psi (adjustable)
Fixed pressure to 160 psi
Up to 30,000+ operating hours
Whisper quiet - less than 45 DBA
Can run dry without damage
Self-priming - 60" lift
Low voltage (12-24V) for maximum safety
Corrosion resistant exterior
Continuous or intermittent operation
OPERATION: The 6800 is designed to operate with a PSW Tank Shut-Off Switch for hydro-pneumatic storage systems. The PSW, when used with a typical under-counter R.O. system, can be augmented with an ESO Electronic Shut-Off Valve. It is also compatible with most hydraulic shut-off valves. For counter-top systems, Aquatec's TLC Tank Level Control Switch Valve shut off feed water and the pump when the product water storage tank is full.
---------------------------------------- |
Price: $75.00
|
| CDP 8800 |
POWER: Pumps operate with safe, low energy (only 24 watts), low voltage (12-24 volt) motors, powered with compatible transformers with world wide primary voltages available (100 VAC, 120 VAC, 230 VAC). Transformers are optional and must be ordered in addition to the pump.
MOUNTING: The steel base plate is included at no extra cost. The "Universal" base plate P/N 51-104 is optionally available at no additional cost.
FITTINGS: Built-in 3/8" John Guest half cartridge fittings eliminate need for external fittings (unless elbows are required); Optional at no cost are 3/8" Jaco straight, 3/8" Jaco elbow fittings, or 8mm stem adapters for metric tubing. The location and positioning of the pump may affect its' performance. Consult the factory for recommendations that will optimize your system
|
CDP 8800 Series High Flow Booster Pump
Distinguishing Features
Toughest, most durable pump on market
Adjustable max. outlet psi (regardless of feed pressure)
Expels trapped air (no more air locks)
Can be mounted w/pump head up or down
More flow at extremely low inlet pressures
EMI/RFI electronic noise suppression
New motor venting system to remove moisture
100% final performance tested.
Key Operating Benefits
Boosts pressure 40 to 120 psi (adjustable)
Used with membranes 50 to 100 GDP
15,000+ operating hours
Quiet - less than 52 DBA
Can run dry without damage
Self-priming - 60" lift
Low voltage (12-24V) for maximum safety
Corrosion resistant exterior
OPERATION: The CDP 8800 is designed to operate with a PSW Tank Shut-Off Switch for hydro-pneumatic storage systems. The PSW when used with a typical under-counter R.O. system, can be augmented with an ESO Electronic Shut-Off Valve. It is also compatible with most hydraulic shutoff valves. For counter-top systems, Aquatec's TLC Tank Level Control Switch Valve shut off feed water when the product water storage tank is full. The AFR Auto-Flush Valve is highly recommended for higher production membranes requiring a CDP 8800, to ensure membrane efficiency.
---------------------------------
|
Price: $93.00 |
| ERP 1000 |
 |
ERP 1000 Permeate Pump
Distinguishing Features
For membranes rated from 10 to 120 GDP
Required no electricity
pump powered by energy from brine normally lost to the drain
Improves water quality
Effective for inlet water pressure as low as 30 psi
Fills product tank up to 5 times faster under normal use
Saves 400% of waste water vs. conventional units
Allows smaller capacity membranes
Increases membrane life
Prevents "membrane TDS creep"
Allows greater product tank pressure (90% of feed pressure)
PUMP DESIGN: "Positive displacement, reciprocating, single action diaphragm, hydraulicall driven.
WEIGHT: 1 lb.
WETTED MATERIALS-PERMEATE SIDE: NSF listed and FDA approved thermoplastic, EPDM.
NON-WETTED MATERIALS: Stainless Steel, Polypropylene.
MOUNTING: Always mount pump with outlet ports up. Mounting clip (ABS) with (2) #10 S.S. screws available.
FITTINGS: Optional Jaco or John Guest straight or elbow
------------------------------------------
|
Price: $58.00
|
| DDP 5800 & 7800 |
POWER: The power demand varies depending on flow and pressure from 25W to 100W. Motors are available in various configurations from 12 VDC to 230 VAC. Transformers or DC power supplies are optional and must be ordered separately if applicable. Standard terminations are 12" Long 16 AWG leadwires with a stripped end, connectors or cords with plugs are optional. MOUNTING: A steel mounting base with four hollow rubber grommets is standard and included at no extra cost. The pump may be mounted in any position.
FITTINGS: The 5800 pump is offered with either an integral John Guest style quick connect push-in fitting for 3/8" OD semi-rigid tubing, or a straight or elbow 3/8" Jaco style external fitting. The 7800 pumphead has a .625" port opening that accepts "quick-connect" beverage style O-ringed barb fittings, for use with 3/8" ID tubing. Always consult the factory for recommendations that will optimize your system |
DDP 5800 & 7800 Delivery/Demand Pump
Distinguishing Features
3 chamber construction
Closed impervious diaphragm
Asymmetrical manifold
Integral switch or bypass
Highest structural integrity
Seven point clamping
Engineered composite plastics
Corrosion resistant metal
Multiple porting options
DC and AC motors
Key Operating Benefits
.25 to 1.5 GPM (5lpm) flow
Up to 130 psi (9 bars) pressure
Adjustable switch and bypass settings
Auto purging
7 year design life
Highly efficient
Minimal pulsations
Whisper quiet at lower flows
Self priming
Can run dry without damage
Chemically resistant versions
OPERATION: The 5800/7800 pumps can draw water from a holding tank and pressurize it, or boost the pressure from a low pressure source. They are designed to operate intermittently, but most versions can run continuously for several hour intervals. The pumps can be operated in demand mode controlled by an integral pressure switch, or in delivery mode controlled by an external power switching device. An integral bypass may be used to limit pressure.
------------------------------------------- |
DDP 5800
Price: $126.99
DDP 7800
Price: $202.00
|
| DDP 8801 |
 |
DDP 8801 Series High Flow Booster Pump
Distinguishing Features
Easy retrofit to existing installations
Decorative appliance grade, white ABS housing
Self-contained pump system
Built-in100 mesh screen filter
100% inspected and factory tested
MOUNTING: Pump should always be mounted after the feed water shut off valve in front of any filter to prevent dust from clogging the valves.
OPTIONS: 12 or 24 volts AC or DC; 1/4" quick disconnect John Guest fittings; On/Off switch with either a 2 or 4 hour timer circuit; AFR Auto-Flush Valve to improve membrance performance; LDS Leak Detector Sensor Valve to prevent water damage; LPS Low Pressure Switch. .Ability to mount ESO Electronic Shut-Off Valve inside housing.
----------------------------------------- |
Price: $101.50 |
|
