|
|
Frame Mount Horizontal
FRAME MOUNT HORIZONTAL
GPD: 10,000 - 23,000
- Skid-Mounted Design with durable powder-coated frame
- Designed for municipal/tap water source, operating system pressure at 200 psi.
- Quality components utilized for system construction
- Dependable electro-mechanical relay logic control circuit
- Dual-Level tank switchesand controls
- Plumbed for optimum water recovery
- Victaulic coupling for ease of maintenance
- Sampling valves for monitoring each membrane vessel
- Stainless steel multi-stage centrifugal pump
- Water quality monitoring
- Higher flow rates above 24,000 gallons per day available.
- Output Production: 10,000 gpd to 24,000 gpd
|
 |
STANDARD FEATURES
- Powder-coated steel frame
- Stainless steel high-pressure multi-stage pump
- Thin film composite membrane
- 80” PVC membrane housings
- Sch 80 PVC manifolding
- Liquid-filled pre/post filter press. gauges
- Liquid-filled feed & conc. press. gauges
- Liquid-tight wire shrouding
- Motorized inlet ball valve
- Adjustable s.s. concentrate valve
- Product & waste flow meters
- Product sampling valves for each vessel
- 20” 5 micron pre-filters (2)
- Victaulic couplings on membrane manifolding
- Stainless steel throttling valve
- Fused main disconnect switch
- Aluminum diamond plate on skid base
- Low voltage dual-level product switches
- Automatic hourly fast flush
- Optimum performance membrane array
|
STANDARD ELECTRICAL CONTROLS
- NEMA 4 fiberglass enclosure
- Off/On switch
- Dual level float switches
- Low pressure switch
- Low pressure bypass delay
- Fused control circuit
- 24 volt level control circuit
- Time delay start
- IEC motor contactor w/overload relay
- High pressure cut-out w/auto restart
- High pressure instant start reset button
- Solid state hourly fast flushing timer
- Digital TDS monitor (1 - 99 ppm range)
- Pre-treatment backwash or regenerating lock-out
Lights: power, running, flushing, low pressure, high pressure, tank full, pre-treatment lock-out, high pressure
OPTIONS:
- Stainless steel membrane housings
- Fiberglass membrane housings
- Stainless steel manifolding
- pH monitor control
- Higher operating pressures
- Higher product flow output
- Membrane cleaning ports
- Chemical or antiscalant injection
- 50 hz electrical requirement
- Shipping crate
- Other options available upon request
|
FEED WATER PARAMETERS:
STemperature 85o F maximum SPressure 40 - 80 psi maximum STDS 2000 ppm maximum. If higher, consult factory SIron tolerance 0.5 ppm maximum SHydrogen sulfide must be removed S Silica tolerance can not be higher than 125 ppm in the concentrate stream. Antiscalant should be considered for any levels over 75 ppm. STurbidity should be removed SHardness must be removed. OPERATING PARAMETERS: SOperating pressure 200 psi maximum SWater recovery rates are decided at time of system design. Water chemistry, pre-treatment and membrane array will determine the recovery ratio. Recovery rates are approximately 70-75% (min. 65%, max. 80%) SpH range 3 - 11 SFlow rates are determined by the membrane mfgr’s. testing criteriea of 1500 ppm Nacl solution, 77oF water temperature, 225 psi at 10-15% recovery. Actual flow rates may vary depending on the pre-treatment used, water conditions, system size, membrane array and applied pressure. |
MODEL |
GPD
(minimum) |
MEMBRANE |
MOTOR |
PIPING
inlet waste |
DIMENSIONS |
Order |
Price |
FMH3-2 |
9,000 - 10,800 |
4” x 40” 6ea. |
5 HP |
1 ½” 1” 1” |
110” x 31” x 66”H |
|
$13,000.00 |
FMH4-2 |
12,000 - 14,400 |
4” x 40” 8ea. |
5 HP |
1 ½” 1” 1” |
110” x 31” x 66”H |
|
$14,000.00 |
FMH5-2 |
15,000 - 17,400 |
4” x 40” 10ea. |
7.5 HP |
1 ½” 1” 1” |
110” x 31” x 66”H |
|
$15,000.00 |
FMH6-2 |
18,000 - 20,000 |
4” x 40” 12ea. |
7.5 HP |
1½” 1” 1” |
110” x 31” x 66”H |
|
$16,300.00 |
FMH7-2 |
21,000 - 23,000 |
4” x 40” 14ea. |
7.5 HP |
1½” 1” 1” |
110” x 31” x 66”H |
|
$17,500.00 |
|
|
