|
|
Frame Mount Vertical
FRAME MOUNT VERTICAL
GPD: 800 - 10,800
- Floor standing Model, with durable powder-coated frame.
- Designed for municipal/tap water source, operating system pressure at 200 psi
- Quality components utilized for system construction
- Dependable electro-mechanical relay logic control circut
- Dual-level tank switches and controls
- Plumbed for optimum water recovery
- 12 Month (One Year) Factory Warranty
- Output Production: 800 gpd up to 10,800 gpd
|
  |
STANDARD FEATURES
- Powder-coated steel frame
- Stainless steel multi-stage pump
- Thin film composite membrane
- PVC membrane housing
- High-pressure nylon tubing
- Liquid-filled high pressure gauge
- Liquid-tight wire shrouding
- Feed water inlet solenoid valve
- Adjstbl. waste & recycle needle valves
- Product & waste flow meters
- 5 micron pre-filter
- Inlet and outlet pre-filter gauges
- High-pressure brass comp. fittings
- Salt rejection 95 - 99%
|
STANDARD ELECTRICAL CONTROLS
- NEMA 4 fiberglass enclosure
- Off/On switch
- Dual level float switches
- Low pressure switch
- Low pressure bypass delay
- Fused control circuit
- 24 volt level control circuit
- Time delay start
- 30 amp motor contactor
Lights: power, running, low pressure, tank full
OPTIONS:
- Stainless steel membrane housings
- Automatic hourly flush
- Manual flush
- TDS monitor (digital or analog)
- Hour meter
- Recycle flow meter
- Tank pressure switch (product)
- Product diversion
- IEC contactor, with overload
- Stainless steel needle valves
- High pressure cut-off w/auto restart and manual override
- Pre-treat lock-out with light
- 50 hz electrical requirement
- Shipping crate
- Other options available upon request
|
FEED WATER PARAMETERS:
STemperature 85o F maximum SPressure 40 - 80 psi maximum STDS 2000 ppm maximum. If higher, consult factory SIron tolerance 0.5 ppm maximum SHydrogen sulfide must be removed S Silica tolerance can not be higher than 125 ppm in the concentrate stream. Antiscalant should be considered for any levels over 75 ppm. STurbidity should be removed SHardness must be removed. OPERATING PARAMETERS: SOperating pressure 200 psi maximum SWater recovery rates are decided at time of system design. Water chemistry, pre-treatment and membrane array will determine the recovery ratio. Recovery rates are approximately 70-75% (min. 65%, max. 80%) SpH range 3 - 11 SFlow rates are determined by the membrane mfgr’s. testing criteriea of 1500 ppm Nacl solution, 77oF water temperature, 225 psi at 10-15% recovery. Actual flow rates may vary depending on the pre-treatment used, water conditions, system size, membrane array and applied pressure.
|
MODEL |
GPD
(minimum) |
MEMBRANE |
MOTOR |
PUMP |
PIPING
inlet waste |
DIMENSIONS |
Order |
Price |
FMV-1 |
1,500 - 2,000 |
4” x 40” 1ea. |
1 HP |
multi-stage |
3/4” 1/2” 1/2” |
24” x 29” x 57”H |
|
$3175.00 |
FMV-2 |
3,000 - 4,000 |
4” x 40” 2ea. |
2 HP |
multi-stage |
1” 1/2” 1/2” |
110” x 31” x 66”H |
|
$3775.00 |
FMV-3 |
4,500 - 6,000 |
4” x 40” 3ea. |
2 HP |
multi-stage |
1” 1/2” 1/2” |
110” x 31” x 66”H |
|
$4475.00 |
FMV-4 |
6,000 - 8,000 |
4” x 40” 4ea. |
3 HP |
multi-stage |
1” 1/2” 1/2” |
110” x 31” x 66”H |
|
$5050.00 |
FMV-5 |
7,500 - 9,000 |
4” x 40” 5ea. |
3 HP |
multi-stage |
1” 1/2” 1/2” |
110” x 31” x 66”H |
|
$5475.00 |
FMV-6 |
9,000 -10,800 |
4” x 40” 6ea. |
3 HP |
multi-stage |
1” 1/2” 1/2” |
110” x 31” x 66”H |
|
$6200.00 |
|
|
